airlitefix:start
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revisionLast revisionBoth sides next revision | ||
airlitefix:start [2020/05/28 16:17] – support | airlitefix:start [2021/03/08 09:47] – support | ||
---|---|---|---|
Line 1: | Line 1: | ||
- | \\ | + | |
**__Question: | **__Question: | ||
\\ | \\ | ||
Line 54: | Line 54: | ||
------ | ------ | ||
\\ | \\ | ||
+ | ===== How to open an Airlite in the right order ===== | ||
+ | \\ | ||
+ | To open an Airlite follow the next steps carefully.\\ | ||
+ | \\ | ||
+ | === Be sure that the unit is unplugged from the power source! === | ||
+ | \\ | ||
+ | ===To swap a Airlite 4x P.C.B. or backplane you don't have to disassamble the complete unit!=== | ||
+ | \\ | ||
+ | {{: | ||
+ | \\ | ||
+ | To open an Airlite you need to remove all the Potentiometer knobs and fader knobs.\\ | ||
+ | \\ | ||
+ | \\ | ||
+ | {{: | ||
+ | \\ | ||
+ | Remove the screws in the Red circles at the picture.\\ | ||
+ | \\ | ||
+ | \\ | ||
+ | {{: | ||
+ | \\ | ||
+ | The Airlite 4x is situated at the bottom side of the Main P.C.B..\\ | ||
+ | \\ | ||
+ | \\ | ||
+ | {{: | ||
+ | \\ | ||
+ | Remove the screws in the Red circles at the picture and all the potentiometer nuts.\\ | ||
+ | \\ | ||
+ | \\ | ||
+ | ------- | ||
+ | \\ | ||
+ | ====How to remove the Power supply==== | ||
+ | \\ | ||
+ | {{: | ||
+ | \\ | ||
+ | The power supply is located at the right side.\\ | ||
+ | \\ | ||
+ | \\ | ||
+ | {{: | ||
+ | \\ | ||
+ | Remove the screws in the Red circles at the picture.\\ | ||
+ | \\ | ||
+ | \\ | ||
+ | {{: | ||
+ | \\ | ||
+ | Remove the screws in the Red circles at the picture.\\ | ||
+ | \\ | ||
+ | ----- | ||
+ | \\ | ||
+ | ====How to remove the backplane==== | ||
+ | \\ | ||
+ | {{: | ||
+ | \\ | ||
+ | Remove the screws in the Red circles at the picture.\\ | ||
+ | \\ | ||
+ | \\ | ||
+ | {{: | ||
+ | \\ | ||
+ | Remove the screws in the Red circles at the picture.\\ | ||
+ | \\ | ||
+ | \\ | ||
+ | {{: | ||
+ | \\ | ||
+ | Remove the screws in the Red circles at the picture.\\ | ||
+ | \\ | ||
+ | -------- | ||
+ | \\ | ||
+ | ====Where to place the AES3 module in an Airlite==== | ||
+ | \\ | ||
+ | {{: | ||
+ | \\ | ||
+ | The position of the AES3 board is on these pin strips at the backplane.\\ | ||
+ | This can be installed easily if you need an Master to AES3 output at a later moment.\\ | ||
+ | \\ | ||
+ | -------- | ||
+ | \\ | ||
+ | ====Where to measure the Power supply in an Airlite==== | ||
+ | \\ | ||
+ | {{: | ||
+ | \\ | ||
+ | The ground is marked with a Green dot.\\ | ||
+ | The Red dot is the Possitive (+ 15 Volt) voltage.\\ | ||
+ | The Blue dot is the Possitive (- 15 Volt) voltage.\\ | ||
+ | The Purple dot is the Logic (+ 5 Volt) voltage.\\ | ||
+ | The Purple dot is the Phantom power (+ 48 Volt) voltage.\\ | ||
+ | \\ | ||
+ | \\ | ||
+ | {{: | ||
+ | \\ | ||
+ | In this picture you can see an overview of the Power distribution.\\ | ||
\\ | \\ | ||
----- | ----- | ||
Line 64: | Line 152: | ||
[[https:// | [[https:// | ||
\\ | \\ | ||
- | Go back to the [[SupAirlite: | + | [[start: |
- | \\ | + | |
airlitefix/start.txt · Last modified: 2022/07/18 09:07 by support