lyrauserlevels:start
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revisionLast revisionBoth sides next revision | ||
lyrauserlevels:start [2018/12/12 09:27] – support | lyrauserlevels:start [2020/06/12 11:36] – support | ||
---|---|---|---|
Line 1: | Line 1: | ||
**__Question: | **__Question: | ||
**__Answer: | **__Answer: | ||
+ | \\ | ||
To create Users and different User levels you'll have to follow these steps:\\ | To create Users and different User levels you'll have to follow these steps:\\ | ||
+ | \\ | ||
1. Create at the web page “Security Settings” and “Users and Levels” an Admin account first with the User level " | 1. Create at the web page “Security Settings” and “Users and Levels” an Admin account first with the User level " | ||
Protect this account with a Password and click “update”. \\ | Protect this account with a Password and click “update”. \\ | ||
Now you'll have an account without any restrictions.\\ | Now you'll have an account without any restrictions.\\ | ||
+ | \\ | ||
2. Remove other accounts. \\ | 2. Remove other accounts. \\ | ||
+ | \\ | ||
3. Go to “Securuty Settings” and “Chipcard settings”. \\ | 3. Go to “Securuty Settings” and “Chipcard settings”. \\ | ||
Insert a chipcard and refresh the website.\\ | Insert a chipcard and refresh the website.\\ | ||
+ | \\ | ||
4. After refreshing the Lyra should show the detected chip card at surface 2. \\ | 4. After refreshing the Lyra should show the detected chip card at surface 2. \\ | ||
Select “Control surface 2 chip card determines user level for control surface 1 (for 8 fader 19" Surface)” and click update. \\ | Select “Control surface 2 chip card determines user level for control surface 1 (for 8 fader 19" Surface)” and click update. \\ | ||
+ | \\ | ||
5. Then type "Admin name" at chip card name with it's password (2x). \\ | 5. Then type "Admin name" at chip card name with it's password (2x). \\ | ||
Then press “write to ChipCard”. \\ | Then press “write to ChipCard”. \\ | ||
+ | \\ | ||
6. Now you go to “Securuty Settings” and “Network Levels”. \\ | 6. Now you go to “Securuty Settings” and “Network Levels”. \\ | ||
Here you select of all user levels, all the functions (Also select FTP authorities) and click “update”.\\ | Here you select of all user levels, all the functions (Also select FTP authorities) and click “update”.\\ | ||
It isn't possible to change the authorities of the “System Administrator”.\\ | It isn't possible to change the authorities of the “System Administrator”.\\ | ||
+ | \\ | ||
7. To check click "log off" at the first page of the web interface.\\ | 7. To check click "log off" at the first page of the web interface.\\ | ||
+ | \\ | ||
8. Close all browsers and wait for one minute.\\ | 8. Close all browsers and wait for one minute.\\ | ||
If you don't close the browser the Lyra will keep alive the active connection and won't ask to log in again.\\ | If you don't close the browser the Lyra will keep alive the active connection and won't ask to log in again.\\ | ||
+ | \\ | ||
9. Open a new browser and go to the IP address of the Lyra.\\ | 9. Open a new browser and go to the IP address of the Lyra.\\ | ||
+ | \\ | ||
10. The Lyra will now ask to log in with the user name and password.\\ | 10. The Lyra will now ask to log in with the user name and password.\\ | ||
To create extra users or to change there security levels you now have to login with the Admin account.\\ | To create extra users or to change there security levels you now have to login with the Admin account.\\ | ||
+ | \\ | ||
11. When you login with an other user you won't get the possiblity to change settings of the Lyra.\\ | 11. When you login with an other user you won't get the possiblity to change settings of the Lyra.\\ | ||
+ | \\ | ||
{{ : | {{ : | ||
- | + | \\ | |
- | [[https:// | + | [[https:// |
+ | \\ | ||
+ | [[start: | ||
+ | \\ |
lyrauserlevels/start.txt · Last modified: 2022/07/18 09:27 by support