Both sides previous revisionPrevious revisionNext revision | Previous revisionNext revisionBoth sides next revision |
supairence:start [2022/01/10 14:13] – support | supairence:start [2023/04/12 16:43] – roger |
---|
| |
\\ | \\ |
====== Attention ! ====== | ====== Attention ====== |
^ Be carefull due to a hardware change it isn't possible to combine older versions with units produced after 01-01-2022 !!! ^^^ | ^ Be carefull due to a hardware change it is NOT possible to combine older versions with units produced after 01-01-2022. ^^^ |
| V.10 Main\\ V.6 Ext | 01-01-2022 | POWER SUPPLY CHANGED TO 12 VOLT INSTEAD OF THE EARLIER USED 36 VOLT\\ MAIN V.10 and EXTENDER V.6 ARE NOT COMPATIBLE WITH OLDER VERSIONS !!! | | | V.10 Main\\ V.10 Extender | 01-01-2022 | POWER SUPPLY CHANGED TO 12 VOLT INSTEAD OF THE EARLIER USED 36 VOLT\\ MAIN V.10 and EXTENDER V.10 ARE NOT COMPATIBLE WITH OLDER VERSIONS. \\ Connecting a older to a newer units will damage the older unit. | |
\\ | \\ |
Install as Administrator :!: \\ | Install as Administrator :!: \\ |
To set the unit in bootloader mode: | To set the unit in bootloader mode: |
- Take off the Power off the unit | - Take off the Power off the unit |
- Hold down the "Encoder" of the "Control surface" | - Hold down the "Encoder" (Data) of the "Control surface" |
- While holding down the "Encoder" you'll have to "Power on" the unit | - While holding down the "Encoder" (Data) you'll have to "Power on" the unit |
- Release the "Encoder" after 5 seconds | - Release the "Encoder" (Data) after 5 seconds |
- The Unit will show some random LED's as there is no software loaded at this moment | - The Unit will show some random LED's as there is no software loaded at this moment |
\\ | \\ |
| If you receive a Error 740, it means that it requires elevation to run.\\ |
| Meaning you must run it as administrator.\\ |
| Try right clicking the command prompt and running it as administrator.\\ |
\\ | \\ |
^ Needed Software ^ Windows 7 {{:compatibility-windows-7.jpg?80|}} ^ Windows 8 {{:compatibility-windows-8.jpg?80|}} ^ Windows 10 {{:compatibility-windows-10.jpg?80|}} ^ Windows 11 {{:compatibility-windows-11.jpg?80|}} ^ MAC OS X {{:compatibility-mac.jpg?80|}} ^ Linux\\ {{:compatibility-linux.jpg?90|}} ^ Manual\\ & Info ^ | ^ Needed Software ^ Windows 7 {{:compatibility-windows-7.jpg?80|}} ^ Windows 8 {{:compatibility-windows-8.jpg?80|}} ^ Windows 10 {{:compatibility-windows-10.jpg?80|}} ^ Windows 11 {{:compatibility-windows-11.jpg?80|}} ^ MAC OS X {{:compatibility-mac.jpg?80|}} ^ Linux\\ {{:compatibility-linux.jpg?90|}} ^ Manual\\ & Info ^ |
| Firmware Updatetool | [[http://www.mambanet.org/wiki/dokudata/software/Firmware Updatetool v4.10 - Setup.exe| v4.10]] |||| N/A | N/A | [[http://www.mambanet.org/wiki/dokudata/software/Firmware Update v4.1.pdf|PDF]] | | | Firmware Updatetool | [[http://www.mambanet.org/wiki/dokudata/software/Firmware Updatetool v4.10 - Setup.exe| v4.10]] (Needs Java 32bits, Visual Studio and driver!) |||| N/A | N/A | [[http://www.mambanet.org/wiki/dokudata/software/Firmware Update v4.1.pdf|PDF]] | |
| AtLibUsbDfu.dll installer\\ <sub>(Needed for Firmware update tool)</sub> | [[http://www.mambanet.org/wiki/dokudata/software/driver-atmel-installer-x86-7.0.1931.msi|Driver X86]]\\ [[http://www.mambanet.org/wiki/dokudata/software/driver-atmel-installer-x64-7.0.1931.msi|Driver X64]]\\ or [[https://youtu.be/oWNRIsJQvCk|Video AtLibUsbDfu.dll]] <sub>-> Shown as Unknown Device !</sub> |||| - | - | - | | | AtLibUsbDfu.dll installer\\ <sub>(Needed for Firmware update tool)</sub> | [[http://www.mambanet.org/wiki/dokudata/software/driver-atmel-installer-x86-7.0.1931.msi|Driver X86]]\\ [[http://www.mambanet.org/wiki/dokudata/software/driver-atmel-installer-x64-7.0.1931.msi|Driver X64]]\\ or [[https://youtu.be/oWNRIsJQvCk|Video AtLibUsbDfu.dll]] <sub>-> Shown as Unknown Device !</sub> |||| - | - | - | |
| Java 32 bits\\ <sub>(Needed for Firmware update tool) (A)</sub> | [[https://javadl.oracle.com/webapps/download/AutoDL?BundleId=238726_478a62b7d4e34b78b671c754eaaf38ab|Java X86]] |||| - | - | - | | | Java 32 bits\\ <sub>(Needed for Firmware update tool) (A)</sub> | [[https://javadl.oracle.com/webapps/download/AutoDL?BundleId=238726_478a62b7d4e34b78b671c754eaaf38ab|Java X86]] |||| - | - | - | |
|**__Answer:__** Take a look at this picture:| | |**__Answer:__** Take a look at this picture:| |
|{{:voiptelephoneoptions.jpg?600|}}| | |{{:voiptelephoneoptions.jpg?600|}}| |
| \\ |
| ^**__Question:__** How can I connect a (GSM) Hybrid to my Voip channel?^ |
| |**__Answer:__** Connect the output from the Hybrid to the input of the Voip channel and the Cleanfeed output to the input of your Hybrid. Therefor you need to make a cable from the RJ11 connector to input connector on your hybrid:| |
| |{{:voip-cleanfeed-to-hybrid.png?800|}}| |
\\ | \\ |
^**__Question:__** How to use the Voip channel in my mixer?^ | ^**__Question:__** How to use the Voip channel in my mixer?^ |
^**__Question:__** I want to connect my Fader start to my CD player, Turntable or other player, how do I have to connect this?^ | ^**__Question:__** I want to connect my Fader start to my CD player, Turntable or other player, how do I have to connect this?^ |
|**__Answer:__** Instructions can be found in this webpage: [[faderstartinstr:start|Fader start instructions]]| | |**__Answer:__** Instructions can be found in this webpage: [[faderstartinstr:start|Fader start instructions]]| |
| \\ |
| * [[http://www.mambanet.org/wiki/dokudata/faq/airlite/How to Connect Mika-Arm to Airlite.pdf|How to Connect Mika-Arm to my mixing desk]] |
\\ | \\ |
* [[http://www.mambanet.org/wiki/dokudata/faq/airence/Akiyama_fdstart.pdf|Akiyama Faderstart]] | * [[http://www.mambanet.org/wiki/dokudata/faq/airence/Akiyama_fdstart.pdf|Akiyama Faderstart]] |