Differences

This shows you the differences between two versions of the page.

--- usbauxmod:start [2019/10/23 13:54] – created support
+++ usbauxmod:start [2022/07/18 09:11] (current) – support
@@ Line 5: / Line 5: @@
 \\
 \\
-===== Under construction =====
+-----
 \\
+==== This modification is standard for Version 10 with serial number 191001xx-V10 which means produced 2019-10-01 or later. ====
+\\
+-----
+\\
+===== For latest models with SMD components (Version 4 or later) =====
+\\
+{{ :usbauxmod:l-r_omgedraaid_-ombouw-auxnaar_usb.jpg?direct&800 |}}
+\\
+\\
+Place both Jumpers on the PCB's edge positions of the Jumper header.\\
+Solder 2 wires to this position of the Jumper headers.\\
+These pins are already connected on the PCB, for strength we suggest to solder it to both pins.\\
+Black has to be connected to Left and Green has to be connected to Right!\\
+\\
+\\
+{{ :usbauxmod:auxtousb3.jpg?direct&800 |}}
+\\
+Connect the 2 Pin female connector to this male pcb connector or solder the wires to these pins.\\
+Black has to be connected to Left and Green has to be connected to Right!\\
+\\
+\\
+-----
+\\
+===== For older models with leaded components (Version 3 or earlier) =====
+\\
+{{ :usbauxmod:auxtousb1.jpg?direct&800 |}}
+\\
+Place jumpers in this position\\
+\\
+\\
+{{ :usbauxmod:auxtousb2.jpg?direct&800 |}}
+\\
+Solder 2 wires to this position of the Jumper headers.\\
+These pins are already connected on the PCB, for strength we suggest to solder it to both pins.\\
+Black has to be connected to Left and Green has to be connected to Right!\\
+\\
+\\
+{{ :usbauxmod:auxtousb3.jpg?direct&800 |}}
+\\
+Connect the 2 Pin female connector to this male pcb connector or solder the wires to these pins.\\
+Black has to be connected to Left and Green has to be connected to Right!\\
+\\
+\\
+-----
+\\
+===== For models that don't have the 2 pin Auxilary connector at the Master 2 (Left) PCB =====
+\\
+{{ :usbauxmod:auxtousb1.jpg?direct&800 |}}
+\\
+Place jumpers in this position\\
+\\
+\\
+{{ :usbauxmod:airmate_leaded_aux_to_usb_usb_pcb.jpg?direct&800 |}}
+\\
+Solder 2 wires to this position of the Jumper headers.\\
+These pins are already connected on the PCB, for strength we suggest to solder it to both pins.\\
+Black has to be connected to Left and Red has to be connected to Right!\\
+\\
+\\
+{{ :usbauxmod:airmate_leaded_aux_to_usb_master_left.jpg?direct&800 |}}
+\\
+On the Master 2 (Left) PCB you'll find 2 resistors next to the Auxilary send RCA connector.\\
+Solder the Red and Black wire to the points as in the example.\\
+\\
+\\
+If you have questions, please consult the factory by filling in our Support Request form.\\
+\\
+[[https://www.dnrbroadcast.com/support-related|Support Request]]\\
+\\
+[[start:|{{:iconhome.png?100|Home}}]][[SupAirmate:start|{{:iconback2.png?100|Back}}]]
+\\