=====Multiple Axum settings=====
\\
^**__Question:__** How can I configure my Axum to control Aircast?^
|**__Answer:__** Link: [[axumaircast:start|follow the instructions on this page]]|
\\
^**__Question:__** How can I move the Motorfaders by pressing a button?^
|**__Answer:__** Link: [[axumsettings:start#motorfader|follow the instructions on this page]]|
\\
^**__Question:__** How can I add the Source gain function to other cards then the MicAD card?^
|**__Answer:__** Link: [[axumsettings:start#gain|follow the instructions on this page.]]|
\\
^**__Question:__** How can I add the Destination gain function to an output card?^
|**__Answer:__** Link: [[axumsettings:start#gain|follow the instructions on this page.]]|
\\
^**__Question:__** How can I change the color of the LED's in the switches?^
|**__Answer:__** Link: [[axumsettings:start#color|follow the instructions on this page.]]|
\\
^**__Question:__** How can I configure an insert function?^
|**__Answer:__** Link: [[axumsettings:start#insert|follow the instructions on this page.]]|
\\
^**__Question:__** How can I configure an aux function?^
|**__Answer:__** Link: [[axumsettings:start#aux|follow the instructions on this page.]]|
\\
^**__Question:__** How can I configure a headphone Split function?^
|**__Answer:__** Link: [[axumsettings:start#split|follow the instructions on this page.]]|
\\
^**__Question:__** How can I configure a preset to switch to Non Stop mode?^
|**__Answer:__** Link: [[axumsettings:start#nonstop|follow the instructions on this page.]]|
\\
^**__Question:__** How can I configure Talkback?^
|**__Answer:__** Link: [[axumsettings:start#talkback|follow the instructions on this page.]]|
\\
\\
-----
\\
=====Motorfader=====
\\
{{ :axumsettings:motor_fader_up_trigger_start_1.png?direct |}}\\
\\
Changing the function of the __Start__ and __Stop__ buttons at the Surface configuration of each __UI__ __(User Interface)__ to __Module x: Fader on__ and __Module x: Fader off__ will make the fader go up or down when pushing the button.\\
\\
{{ :axumsettings:motor_fader_up_trigger_start_2.png?direct |}}\\
\\
When you change the __Start__ and __Stop__ __Trigger__ at the __Source Configuration__ to __Module fader on__ and __Module fader off__ the Axum will still send out the fader __Start__ and __Stop__ function to the configured GPO's.\\
\\
-----
\\
=====Gain=====
\\
===Source Gain===
\\
{{ :axumsettings:source_gain_at_line_or_aes_input_card.jpg?direct |}}
\\
This example shows how the source gain can be added to other cards then the MicAD.\\
\\
===Destination Gain===
\\
{{:axumsettings:axumadddestinationlevel1.png?direct|}}
\\
This example shows how the destination gain can be added to output cards.\\
\\
{{:axumsettings:axumadddestinationlevel2.png?direct|}}
\\
The level setting will now be available at the Destination configuration.\\
\\
-----
\\
=====Color=====
\\
{{ :axumsettings:ledcolour.png?direct |}}
\\
By changing the __"Switch x.x on color"__ or __"Switch x.x off color"__ to __1 = Green__, __2 = Red__ or __3 = Orange__ you can change it's color. Setting it to __0__ wil switch it __"Off"__.\\
\\
-----
\\
=====Insert=====
\\
{{ :axumsettings:insert1.png?direct |}}
\\
Create an output that sends the __"Mic 1"__ to the __"Left"__ output only.\\
\\
Create a second output that sends the __"Mic 2"__ to the __"Right"__ output only.\\
\\
These can be connected to the inputs or your effect equipment.\\
\\
{{ :axumsettings:insert2.png?direct |}}
\\
Create an __"Insert"__ input that picks the __"Left"__ and __"Right"__ channel from the same __"Slot x ch x"__ input to make it a stereo input.\\
\\
Create a second __"Insert"__ input that picks the __"Left"__ and __"Right"__ channel from the other same __"Slot x ch x"__ input stereo input.\\
\\
These can be connected to your effect outputs.\\
\\
-----
\\
=====Aux=====
\\
{{:axumsettings:aux01b.png?direct|}}
\\
At the "Source configuration" you'll have to rename a desired input as "Aux Return".\\
\\
{{:axumsettings:aux02.png?direct|}}
\\
At the "Destination configuration" you'll have to rename a desired output as "Aux Send".\\
\\
{{:axumsettings:aux03.png?direct|}}
\\
At the "Module configuration" of each module you can set the "Aux1" to "On" if you want to switch the "Aux1" in a preset.\\
\\
It is also possible to manually set the "Aux1" to "On" / "Off" at the "Control surface".\\
\\
{{:axumsettings:aux04.png?direct|}}
\\
It is possible to use the "Aux Return" as "Extern source" this way it is only available at the "Cue" section of the CRM and Studio outputs.\\
\\
{{:axumsettings:aux05.png?direct|}}
\\
It is also possible to hard route it to a specific output.\\
\\
-----
\\
=====Split====
\\
{{ :axumsettings:split_out_1.jpg?direct |}}
\\
Create an output (Line or AES) with on the Left side the PFL and the right side no output. Now create a second line with the Left side no ouput and the right side the Prog as an ouput.\\
\\
Connect this output to an input.\\
\\
{{ :axumsettings:split_out_2.jpg?direct |}}
\\
When you configure this input as an External input it can be directly routed to the headphone.\\
\\
-----
\\
=====Nonstop====
\\
{{:axumsettings:01moduleassignment.png?direct |}}
\\
At the Module assignment page configure the prefered unused modules to work for the desired Console 1.\\
\\
{{:axumsettings:02consoleconfigurationmodule32preset4linein8on.png?direct |}}
\\
At the module configuration create a preset with the Non stop input which also sets on the Program bus for this input.\\ 
\\
{{:axumsettings:03consoleconfigurationmodule32value.png?direct |}}
\\
Let this preset also set on the Module On function and it's value.\\
\\
{{:axumsettings:02consoleconfigurationmodulexxpreset4off.png?direct |}}
\\
Turn off all other module inputs for this preset.\\
\\
{{:axumsettings:04surfaceconfigurationswitch.png?direct |}}
\\
Create a button which switches on the Non stop preset or let it switch by a GPI.\\
\\
=====Talkback====
\\
{{:axumsettings:axum_talkback_configure_english.pdf|View document}}
\\
-----
\\
[[https://www.dnrbroadcast.com/support-related|Support Request]]\\
\\
[[start:|{{:iconhome.png?100|Home}}]][[SupAxum:start|{{:iconback2.png?100|Back}}]]
\\