Differences

This shows you the differences between two versions of the page.

--- airenceversion:start [2020/06/12 12:15] – support
+++ airenceversion:start [2022/01/18 16:16] – support
@@ Line 1: / Line 1: @@
 **__Question:__** What are the differences in versions? \\
 **__Answer:__** Link: [[airenceversion:start|please read the info at this link]]
+\\
+====== Attention ! ======
+^  Be carefull due to a hardware change it is NOT possible to combine older versions with units produced after 01-01-2022 !!!  ^^^
+|  V.10 Main\\ V.10 Extender  |  01-01-2022  |  POWER SUPPLY CHANGED TO 12 VOLT INSTEAD OF THE EARLIER USED 36 VOLT\\  MAIN V.10 and EXTENDER V.10 ARE NOT COMPATIBLE WITH OLDER VERSIONS !!!\\ Connecting a older to a newer units will damage the older unit !!!  |
+\\
 ^  Version  ^  Date  ^  Airence PCB info and modifications  ^
 |  V.1  |  06-12-2013  |  -  |
@@ Line 18: / Line 22: @@
 |    |    |  Airence Main and Extender remove powder coating at 15pin Sub D connector, for better ground connection  |
 ^  ^  ^  ^
-|  V.7  |    |  Airence Main 4, 5 and 6 pcb > SMD with different ledbar drivers  |
+|  V.7  |  xx-06-2016  |  Airence Main 4, 5 and 6 pcb > SMD with different ledbar drivers  |
 |    |    |  Airence Main Added Digital option  |
 |    |    |  Airence 3 (Telco) > SMD with added Ring signal to Start jack  |
@@ Line 25: / Line 29: @@
 |    |    |  __Airence V7 (Telco, Voip, Master 4, 5 and 6 pcb) not compatible with older versions due to Communication buss and Digital option. \\ You'll have to replace the complete set except Airence 6 and 7!__  |
 ^  ^  ^  ^
-|  V.8  |    |  Airence 3 (Telco) > R15, R17 replaced by leaded 600mW Resistors [[https://www.d-r.nl/wiki/dokudata/faq/airence/TELCO AIRENCE MEMO-R17-R18.pdf|R17-R18 modification]]  |
+|  V.8  |  xx-11-2017  |  Airence 3 (Telco) > R15, R17 replaced by leaded 600mW Resistors [[https://www.d-r.nl/wiki/dokudata/faq/airence/TELCO AIRENCE MEMO-R17-R18.pdf|R17-R18 modification]]  |
 ^  ^  ^  ^
-|  V.9  |    |  Airence 3 (Telco) > R15, R17 replaced by SMD High power  |
+|  V.9  |  xx-05-2018  |  Airence 3 (Telco) > R15, R17 replaced by SMD High power  |
+^  ^  ^  ^
+|  V.10 Main\\ V.10 Extender  |  01-01-2022  |  POWER SUPPLY CHANGED TO 12 VOLT INSTEAD OF THE EARLIER USED 36 VOLT\\  MAIN V.10 and EXTENDER V.10 ARE NOT COMPATIBLE WITH OLDER VERSIONS !!!\\ Connecting a older to a newer units will damage the older unit !!!  |
 \\
 [[start:|{{:iconhome.png?100|Home}}]][[SupAirence:start|{{:iconback2.png?100|Back}}]]