airlabversion:start
Differences
This shows you the differences between two versions of the page.
Next revision | Previous revision | ||
airlabversion:start [2018/12/12 13:49] – created support | airlabversion:start [2022/07/18 09:16] (current) – support | ||
---|---|---|---|
Line 3: | Line 3: | ||
^ Version | ^ Version | ||
+ | | MK 1 | Grey coated front Master without SUB potentiometer | ||
+ | ^ ^ ^ | ||
+ | | MK 1 | Grey coated front Master with SUB potentiometer and Talkback potentiometer moved | | ||
+ | ^ ^ ^ | ||
+ | | MK 1 | Grey coated front Channel with 48 volt Phantom power switch | ||
+ | ^ ^ ^ | ||
+ | | MK 1 | Grey coated front Channel with Mono switch and 48 volt Phantom power selected by jumper | ||
+ | ^ ^ ^ | ||
+ | | MK 2 | Silver coated front with added Mic insert | ||
+ | ^ ^ ^ | ||
+ | | MK 2 | Silver coated front with changed side panels and Handrest with D&R logo | | ||
+ | ^ ^ ^ | ||
| DT V.1 | Airlab 7 > Airlab PWR-MO (4 holes to adjust voltages | | DT V.1 | Airlab 7 > Airlab PWR-MO (4 holes to adjust voltages | ||
| | Airlab Mux 5 volt distribution circuit removed | | | Airlab Mux 5 volt distribution circuit removed | ||
Line 8: | Line 20: | ||
| | Airlab USB meter option and control surface added | | | | Airlab USB meter option and control surface added | | ||
| | Airlab VU meter bridge removed | | | Airlab VU meter bridge removed | ||
+ | | | Airlab 2 connect relay circuit changed to work with 5 volt relay | | ||
^ ^ ^ | ^ ^ ^ | ||
| DT V.2 | Airlab PWR-MO > Airlab PSU-A at +/- 15volt | | DT V.2 | Airlab PWR-MO > Airlab PSU-A at +/- 15volt | ||
Line 13: | Line 26: | ||
| DT V.3 | Airlab channel boards to SMD | | | DT V.3 | Airlab channel boards to SMD | | ||
| | Reedrelay at connector board removed, Opto couper placed at channel board to control fader start | | | | Reedrelay at connector board removed, Opto couper placed at channel board to control fader start | | ||
- | | | Airlab 2 connect relay changed to 5 volt | | + | | | Airlab 2 connect relay circuit |
^ ^ ^ | ^ ^ ^ | ||
| DT V.4 | Airlab master boards to SMD | | | DT V.4 | Airlab master boards to SMD | | ||
| | Airlab backplane changed to Lisheng XLR | | | | Airlab backplane changed to Lisheng XLR | | ||
+ | \\ | ||
+ | ^ Airlab channel, USB, Dig, Voip ^ MK2 ^ DT ^ | ||
+ | | Relais | ||
+ | | Resistor R 93 | 2K7 Ohm | 3K48 Ohm | | ||
+ | \\ | ||
+ | ^ Airlab Telco ^ MK2 ^ DT ^ | ||
+ | | Relais RL 1 | 12 volt | 5 volt (no relais at connector PCB, connected with 0 Ohm) | | ||
+ | | Diode Z1 | Zener 8,2 volt | 1N4148 | ||
+ | | Resistor R52 | 120 Ohm | Not placed | ||
+ | | Resistor R 93 | 2K7 Ohm | 3K48 Ohm | | ||
+ | \\ | ||
+ | \\ | ||
+ | ^ Airlab 1x ^ Airlab 10x ^ Airlab PCB info ^ | ||
+ | | Airlab 10A with reed relais (2 jacks) | ||
+ | | | | | ||
+ | | Airlab 10A with reed relais (2 jacks) | ||
+ | | | | | ||
+ | | Airlab 10A with reed relais (2 jacks) | ||
+ | | Airlab 10B with reed relais (3 jacks) | ||
+ | | | | (non insert connect J11) | | ||
+ | | Airlab 10B with reed relais (3 jacks) | ||
+ | | | | (non insert connect J11) | | ||
+ | ^ ^ ^ ^ | ||
+ | | Airlab 10B without reed relais (3 jacks) | ||
+ | | - | - | (non insert connect insert jack at 10B) | | ||
+ | ^ ^ ^ ^ | ||
+ | | Airlab 10A SMT without reed relais insert (3 jacks) | ||
+ | | - | - | (non insert connect jack at 10B) | | ||
+ | \\ | ||
+ | \\ | ||
+ | [[https:// | ||
+ | \\ | ||
+ | [[start: | ||
+ | \\ |
airlabversion/start.1544618941.txt.gz · Last modified: 2018/12/12 13:49 by support