Differences

This shows you the differences between two versions of the page.

--- airlitefix:start [2020/05/28 16:15] – created support
+++ airlitefix:start [2021/03/08 09:47] – support
@@ Line 1: / Line 1: @@
-\\
-**__Question:__** How can I replace or repair a board in an Airmate? \\
+**__Question:__** How can I replace or repair a board in an Airlite? \\
 \\
 **__Answer:__** Link: [[airlitefix:start|please read the info at this link]]
@@ Line 24: / Line 24: @@
 ===== What tools do I need to work on an Airmate =====
 \\
-{{:airmatefix:tool1.jpg?300|}}
+{{:airlitefix:tool1.jpg?300|}}
 \\
 A plastic tool (spatula / spoon) to lift the potentiometer knobs.\\
@@ Line 30: / Line 30: @@
 \\
 \\
-{{:airmatefix:tool2.jpg?300|}}
+{{:airlitefix:tool2.jpg?300|}}
 \\
 A Torx 10 (*) screw driver.\\
@@ Line 36: / Line 36: @@
 \\
 \\
-{{:airmatefix:tool3.jpg?300|}}
+{{:airlitefix:tool3.jpg?300|}}
 \\
 To remove potentiometer nuts a combination pliers with the edges taped in a few layers of painting tape to prevent for scratching.\\
 \\
 \\
-{{:airmatefix:tool4.jpg?300|}}
+{{:airlitefix:tool4.jpg?300|}}
 \\
 Wooden beams to create a distance when the mixer is placed upside down.\\
@@ Line 47: / Line 47: @@
 \\
 \\
-{{:airmatefix:tool5.jpg?300|}}
+{{:airlitefix:tool5.jpg?300|}}
 \\
 A multimeter and some skills to use it.\\
@@ Line 54: / Line 54: @@
 ------
 \\
+===== How to open an Airlite in the right order =====
+\\
+To open an Airlite follow the next steps carefully.\\
+\\
+=== Be sure that the unit is unplugged from the power source! ===
+\\
+===To swap a Airlite 4x P.C.B. or backplane you don't have to disassamble the complete unit!===
+\\
+{{:airlitefix:removeknob.jpg?600|}}
+\\
+To open an Airlite you need to remove all the Potentiometer knobs and fader knobs.\\
+\\
+\\
+{{:airlitefix:airlitefront.jpg?600|}}
+\\
+Remove the screws in the Red circles at the picture.\\
+\\
+\\
+{{:airlitefix:airlite4.jpg?600|}}
+\\
+The Airlite 4x is situated at the bottom side of the Main P.C.B..\\
+\\
+\\
+{{:airlitefix:airlitefrontnutsremoved.jpg?600|}}
+\\
+Remove the screws in the Red circles at the picture and all the potentiometer nuts.\\
+\\
+\\
+-------
+\\
+====How to remove the Power supply====
+\\
+{{:airlitefix:airliterightpsu2.jpg?600|}}
+\\
+The power supply is located at the right side.\\
+\\
+\\
+{{:airlitefix:airliterightpsu.jpg?600|}}
+\\
+Remove the screws in the Red circles at the picture.\\
+\\
+\\
+{{:airlitefix:airliterightpsu3.jpg?600|}}
+\\
+Remove the screws in the Red circles at the picture.\\
+\\
 -----
 \\
-Specific schematics for your Airmate version can be send on request with Serial and version number.\\
+====How to remove the backplane====
+\\
+{{:airlitefix:airliteleft.jpg?600|}}
+\\
+Remove the screws in the Red circles at the picture.\\
+\\
+\\
+{{:airlitefix:airliteright.jpg?600|}}
+\\
+Remove the screws in the Red circles at the picture.\\
+\\
+\\
+{{:airlitefix:airliteconn.jpg?600|}}
+\\
+Remove the screws in the Red circles at the picture.\\
+\\
+--------
+\\
+====Where to place the AES3 module in an Airlite====
+\\
+{{:airlitefix:aespos.jpg?600|}}
+\\
+The position of the AES3 board is on these pin strips at the backplane.\\
+This can be installed easily if you need an Master to AES3 output at a later moment.\\
+\\
+--------
+\\
+====Where to measure the Power supply in an Airlite====
+\\
+{{:airlitefix:airlitemainmeasure.jpg?600|}}
+\\
+The ground is marked with a Green dot.\\
+The Red dot is the Possitive (+ 15 Volt) voltage.\\
+The Blue dot is the Possitive (- 15 Volt) voltage.\\
+The Purple dot is the Logic (+ 5 Volt) voltage.\\
+The Purple dot is the Phantom power (+ 48 Volt) voltage.\\
+\\
+\\
+{{:airlitefix:airlite_1c_component_view_pwrdistri.jpg?600|}}
+\\
+In this picture you can see an overview of the Power distribution.\\
+\\
+-----
+\\
+Specific schematics for your Airlite version can be send on request with Serial and version number.\\
 \\
 If you have questions, please consult the factory by filling in our Support Request form.\\
@@ Line 64: / Line 152: @@
 [[https://www.d-r.nl/support-request.html|Support Request]]\\
 \\
-Go back to the [[SupAirmate:start|Airmate]] support page.\\
+[[start:|{{:iconhome.png?100|Home}}]][[SupAirlite:start|{{:iconback2.png?100|Back}}]]
-\\