axumdante:start
Differences
This shows you the differences between two versions of the page.
Next revision | Previous revisionNext revisionBoth sides next revision | ||
axumdante:start [2021/11/02 09:53] – created support | axumdante:start [2022/06/03 13:48] – support | ||
---|---|---|---|
Line 3: | Line 3: | ||
|**__Answer: | |**__Answer: | ||
\\ | \\ | ||
+ | ----- | ||
+ | \\ | ||
+ | ==== In units produced after 05-05-2021 the Dante card will completly work from slot 12 and higher due to a firmware update. ==== | ||
+ | ==== At units produced after 27-02-2020 the Dante card will completly work in slots 16 to 19. ==== | ||
+ | ==== For units produced before 27-02-2020 take a look at our version table. ==== | ||
+ | \\ | ||
+ | ^**__Question: | ||
+ | |**__Answer: | ||
+ | \\ | ||
+ | ----- | ||
+ | \\ | ||
+ | === Axum side configuration === | ||
+ | \\ | ||
+ | {{: | ||
+ | \\ | ||
+ | First be sure that all the Sources of the Dante card are configured.\\ | ||
+ | \\ | ||
+ | {{: | ||
+ | \\ | ||
+ | The configure all Destinations of the Dante card.\\ | ||
+ | \\ | ||
+ | {{: | ||
+ | \\ | ||
+ | The Axum system will automatically import all settings from the card.\\ | ||
+ | The input levels are set for best results, these can be changed if needed.\\ | ||
+ | \\ | ||
+ | {{: | ||
+ | \\ | ||
+ | The Axum system will automatically import all settings from the card.\\ | ||
+ | The output levels are set for best results, these can be changed if needed.\\ | ||
+ | \\ | ||
+ | ------ | ||
+ | \\ | ||
+ | === Setting up the Dante Virtual soundcard === | ||
+ | \\ | ||
+ | {{: | ||
+ | \\ | ||
+ | When you use the Virtual Soundcard as a WDM soundcard it can go up to 16 x 16 mono channels which is 8 x 8 stereo channels.\\ | ||
+ | \\ | ||
+ | In Asio mode you can go up to 32 x 32 mono channels which is 16 x 16 stereo channels.\\ | ||
+ | \\ | ||
+ | ------ | ||
+ | \\ | ||
+ | === Setting up the Dante Controller === | ||
+ | \\ | ||
+ | {{: | ||
+ | \\ | ||
+ | First it is important that the AXUM dante module is in Sync showing a green square.\\ | ||
+ | \\ | ||
+ | {{: | ||
+ | \\ | ||
+ | Default we deliver the system with the Axum being Clock Master.\\ | ||
+ | This can be set with the blue dot in the Rack Configuration page.\\ | ||
+ | \\ | ||
+ | {{: | ||
+ | \\ | ||
+ | Sometimes when there has been some issues it works better when you set it in the Cards configuration at the Enable word clock setting.\\ | ||
+ | \\ | ||
+ | {{: | ||
+ | \\ | ||
+ | When you use more Dante equipment in your system it can be usefull to set the Dante card as clock master.\\ | ||
+ | \\ | ||
+ | {{: | ||
+ | \\ | ||
+ | When you have issues it can help to change the setting in the cards configuration.\\ | ||
+ | \\ | ||
+ | {{: | ||
+ | \\ | ||
+ | Then it is important to set the Matrix for the Axum inputs.\\ | ||
+ | This way the Dante channels are linked to the Virtual outputs of the PC.\\ | ||
+ | \\ | ||
+ | {{: | ||
+ | \\ | ||
+ | You also need to set the Matrix for the Axum outputs.\\ | ||
+ | This way the Dante channels are linked to the Virtual inputs of the PC.\\ | ||
+ | \\ | ||
+ | Now you can configure the Playout and recording software to work with the Dante Virtual Soundcard in and outputs.\\ | ||
+ | \\ | ||
+ | ------ | ||
+ | \\ | ||
+ | [[https:// | ||
+ | \\ | ||
+ | [[start: | ||
+ | \\ | ||
+ |
axumdante/start.txt · Last modified: 2022/07/18 09:21 by support