Differences

This shows you the differences between two versions of the page.

--- axumdante:start [2021/11/02 09:53] – created support
+++ axumdante:start [2022/07/18 09:21] (current) – support
@@ Line 3: / Line 3: @@
 |**__Answer:__** Link: [[AxumDante:start|follow the instructions on this page.]]|
 \\
+-----
+\\
+==== In units produced after 05-05-2021 the Dante card will completly work from slot 12 and higher due to a firmware update. ====
+==== At units produced after 27-02-2020 the Dante card will completly work in slots 16 to 19. ====
+==== For units produced before 27-02-2020 take a look at our version table. ====
+\\
+^**__Question:__** What are the differences in versions?^
+|**__Answer:__** Link: [[axumversion:start|please read the info at this link]]|
+\\
+-----
+\\
+=== Axum side configuration ===
+\\
+{{:axumdante:dantesources.png?direct|}}
+\\
+First be sure that all the Sources of the Dante card are configured.\\
+\\
+{{:axumdante:dantedestinations.png?direct|}}
+\\
+The configure all Destinations of the Dante card.\\
+\\
+{{:axumdante:danteinputlevel.png?direct|}}
+\\
+The Axum system will automatically import all settings from the card.\\
+The input levels are set for best results, these can be changed if needed.\\
+\\
+{{:axumdante:danteoutputlevel.png?direct|}}
+\\
+The Axum system will automatically import all settings from the card.\\
+The output levels are set for best results, these can be changed if needed.\\
+\\
+------
+\\
+=== Setting up the Dante Virtual soundcard ===
+\\
+{{:axumdante:dantevsc.png?direct|}}
+\\
+When you use the Virtual Soundcard as a WDM soundcard it can go up to 16 x 16 mono channels which is 8 x 8 stereo channels.\\
+\\
+In Asio mode you can go up to 32 x 32 mono channels which is 16 x 16 stereo channels.\\
+\\
+------
+\\
+=== Setting up the Dante Controller ===
+\\
+{{:axumdante:dantecontrollersync.png?direct|}}
+\\
+First it is important that the AXUM dante module is in Sync showing a green square.\\
+\\
+{{:axumdante:axumclockmasterrackconfiguration.png?direct|}}
+\\
+Default we deliver the system with the Axum being Clock Master.\\
+This can be set with the blue dot in the Rack Configuration page.\\
+\\
+{{:axumdante:axumclockmasterrackconfigurationdantecard.png?direct|}}
+\\
+Sometimes when there has been some issues it works better when you set it in the Cards configuration at the Enable word clock setting.\\
+\\
+{{:axumdante:danteclockmasterrackconfiguration.png?direct|}}
+\\
+When you use more Dante equipment in your system it can be usefull to set the Dante card as clock master.\\
+\\
+{{:axumdante:danteclockmasterrackconfigurationdantecard.png?direct|}}
+\\
+When you have issues it can help to change the setting in the cards configuration.\\
+\\
+{{:axumdante:dantecontrolleraxumin.png?direct|}}
+\\
+Then it is important to set the Matrix for the Axum inputs.\\
+This way the Dante channels are linked to the Virtual outputs of the PC.\\
+\\
+{{:axumdante:dantecontrolleraxumout.png?direct|}}
+\\
+You also need to set the Matrix for the Axum outputs.\\
+This way the Dante channels are linked to the Virtual inputs of the PC.\\
+\\
+Now you can configure the Playout and recording software to work with the Dante Virtual Soundcard in and outputs.\\
+\\
+------
+\\
+[[https://www.dnrbroadcast.com/support-related|Support Request]]\\
+\\
+[[start:|{{:iconhome.png?100|Home}}]][[SupAxum:start|{{:iconback2.png?100|Back}}]]
+\\