Differences

This shows you the differences between two versions of the page.

--- supairence:start [2022/01/27 09:55] – support
+++ supairence:start [2023/09/14 01:11] – Updated reference to Firware Update Tool jeroenbol
@@ Line 8: / Line 8: @@
 \\
-====== Attention ! ======
+====== Attention  ======
-^  Be carefull due to a hardware change it is NOT possible to combine older versions with units produced after 01-01-2022 !!!  ^^^
+^  Be carefull due to a hardware change it is NOT possible to combine older versions with units produced after 01-01-2022.   ^^^
-|  V.10 Main\\ V.10 Extender  |  01-01-2022  |  POWER SUPPLY CHANGED TO 12 VOLT INSTEAD OF THE EARLIER USED 36 VOLT\\  MAIN V.10 and EXTENDER V.10 ARE NOT COMPATIBLE WITH OLDER VERSIONS !!!\\ Connecting a older to a newer units will damage the older unit !!!  |
+|  V.10 Main\\ V.10 Extender  |  01-01-2022  |  POWER SUPPLY CHANGED TO 12 VOLT INSTEAD OF THE EARLIER USED 36 VOLT\\  MAIN V.10 and EXTENDER V.10 ARE NOT COMPATIBLE WITH OLDER VERSIONS. \\ Connecting a older to a newer units will damage the older unit.   |
 \\
 Install as Administrator :!: \\
@@ Line 17: / Line 17: @@
 To set the unit in bootloader mode:
   - Take off the Power off the unit
-  - Hold down the "Encoder" of the "Control surface"
+  - Hold down the "Encoder" (Data) of the "Control surface"
-  - While holding down the "Encoder" you'll have to "Power on" the unit
+  - While holding down the "Encoder" (Data) you'll have to "Power on" the unit
-  - Release the "Encoder" after 5 seconds
+  - Release the "Encoder" (Data) after 5 seconds
   - The Unit will show some random LED's as there is no software loaded at this moment
 \\
+If you receive a Error 740, it means that it requires elevation to run.\\
+Meaning you must run it as administrator.\\
+Try right clicking the command prompt and running it as administrator.\\
 \\
 ^  Needed Software  ^  Windows 7 {{:compatibility-windows-7.jpg?80|}}  ^  Windows 8 {{:compatibility-windows-8.jpg?80|}}  ^  Windows 10 {{:compatibility-windows-10.jpg?80|}}  ^  Windows 11 {{:compatibility-windows-11.jpg?80|}}  ^  MAC OS X {{:compatibility-mac.jpg?80|}}  ^  Linux\\ {{:compatibility-linux.jpg?90|}}  ^  Manual\\ & Info  ^
-|  Firmware Updatetool  |  [[http://www.mambanet.org/wiki/dokudata/software/Firmware Updatetool v4.10 - Setup.exe| v4.10]]  ||||  N/A  |  N/A  |  [[http://www.mambanet.org/wiki/dokudata/software/Firmware Update v4.1.pdf|PDF]]  |
+|  Firmware Updatetool  |  [[http://www.mambanet.org/wiki/dokudata/software/D&R Firmware Update Tool v4.11.0 - Setup.exe| v4.11.0]]  (Needs Java 32bits, Visual Studio and driver!)  ||||  N/A  |  N/A  |  [[http://www.mambanet.org/wiki/dokudata/software/Firmware Update v4.1.pdf|PDF]]  |
 |  AtLibUsbDfu.dll installer\\ <sub>(Needed for Firmware update tool)</sub>  |  [[http://www.mambanet.org/wiki/dokudata/software/driver-atmel-installer-x86-7.0.1931.msi|Driver X86]]\\ [[http://www.mambanet.org/wiki/dokudata/software/driver-atmel-installer-x64-7.0.1931.msi|Driver X64]]\\ or   [[https://youtu.be/oWNRIsJQvCk|Video AtLibUsbDfu.dll]] <sub>-> Shown as Unknown Device !</sub>  ||||  -  |  -  |  -  |
 |  Java 32 bits\\ <sub>(Needed for Firmware update tool) (A)</sub>  |  [[https://javadl.oracle.com/webapps/download/AutoDL?BundleId=238726_478a62b7d4e34b78b671c754eaaf38ab|Java X86]]  ||||  -  |  -  |  -  |
@@ Line 168: / Line 170: @@
 ^**__Question:__** I want to connect my Fader start to my CD player, Turntable or other player, how do I have to connect this?^
 |**__Answer:__** Instructions can be found in this webpage: [[faderstartinstr:start|Fader start instructions]]|
+\\
+  * [[http://www.mambanet.org/wiki/dokudata/faq/airlite/How to Connect Mika-Arm to Airlite.pdf|How to Connect Mika-Arm to my mixing desk]]
 \\
   * [[http://www.mambanet.org/wiki/dokudata/faq/airence/Akiyama_fdstart.pdf|Akiyama Faderstart]]