usbauxmod:start
Differences
This shows you the differences between two versions of the page.
Next revision | Previous revision | ||
usbauxmod:start [2019/10/23 13:54] – created support | usbauxmod:start [2022/07/18 09:11] (current) – support | ||
---|---|---|---|
Line 5: | Line 5: | ||
\\ | \\ | ||
\\ | \\ | ||
- | ===== Under construction ===== | + | ----- |
\\ | \\ | ||
+ | ==== This modification is standard for Version 10 with serial number 191001xx-V10 which means produced 2019-10-01 or later. ==== | ||
+ | \\ | ||
+ | ----- | ||
+ | \\ | ||
+ | ===== For latest models with SMD components (Version 4 or later) ===== | ||
+ | \\ | ||
+ | {{ : | ||
+ | \\ | ||
+ | \\ | ||
+ | Place both Jumpers on the PCB's edge positions of the Jumper header.\\ | ||
+ | Solder 2 wires to this position of the Jumper headers.\\ | ||
+ | These pins are already connected on the PCB, for strength we suggest to solder it to both pins.\\ | ||
+ | Black has to be connected to Left and Green has to be connected to Right!\\ | ||
+ | \\ | ||
+ | \\ | ||
+ | {{ : | ||
+ | \\ | ||
+ | Connect the 2 Pin female connector to this male pcb connector or solder the wires to these pins.\\ | ||
+ | Black has to be connected to Left and Green has to be connected to Right!\\ | ||
+ | \\ | ||
+ | \\ | ||
+ | ----- | ||
+ | \\ | ||
+ | ===== For older models with leaded components (Version 3 or earlier) ===== | ||
+ | \\ | ||
+ | {{ : | ||
+ | \\ | ||
+ | Place jumpers in this position\\ | ||
+ | \\ | ||
+ | \\ | ||
+ | {{ : | ||
+ | \\ | ||
+ | Solder 2 wires to this position of the Jumper headers.\\ | ||
+ | These pins are already connected on the PCB, for strength we suggest to solder it to both pins.\\ | ||
+ | Black has to be connected to Left and Green has to be connected to Right!\\ | ||
+ | \\ | ||
+ | \\ | ||
+ | {{ : | ||
+ | \\ | ||
+ | Connect the 2 Pin female connector to this male pcb connector or solder the wires to these pins.\\ | ||
+ | Black has to be connected to Left and Green has to be connected to Right!\\ | ||
+ | \\ | ||
+ | \\ | ||
+ | ----- | ||
+ | \\ | ||
+ | ===== For models that don't have the 2 pin Auxilary connector at the Master 2 (Left) PCB ===== | ||
+ | \\ | ||
+ | {{ : | ||
+ | \\ | ||
+ | Place jumpers in this position\\ | ||
+ | \\ | ||
+ | \\ | ||
+ | {{ : | ||
+ | \\ | ||
+ | Solder 2 wires to this position of the Jumper headers.\\ | ||
+ | These pins are already connected on the PCB, for strength we suggest to solder it to both pins.\\ | ||
+ | Black has to be connected to Left and Red has to be connected to Right!\\ | ||
+ | \\ | ||
+ | \\ | ||
+ | {{ : | ||
+ | \\ | ||
+ | On the Master 2 (Left) PCB you'll find 2 resistors next to the Auxilary send RCA connector.\\ | ||
+ | Solder the Red and Black wire to the points as in the example.\\ | ||
+ | \\ | ||
+ | \\ | ||
+ | If you have questions, please consult the factory by filling in our Support Request form.\\ | ||
+ | \\ | ||
+ | [[https:// | ||
+ | \\ | ||
+ | [[start: | ||
+ | \\ | ||
+ |
usbauxmod/start.1571831668.txt.gz · Last modified: 2019/10/23 13:54 by support