aircastairlite:start
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
aircastairlite:start [2018/12/10 11:00] – support | aircastairlite:start [2020/06/12 12:09] (current) – support | ||
---|---|---|---|
Line 1: | Line 1: | ||
**__Question: | **__Question: | ||
- | **__Answer: | + | **__Answer: |
- | ===== Easy setup manual Aircast with an Airlite ===== | + | ===== Easy setup manual Aircast with an Airlite |
In this Easy setup manual you’ll learn how to set up Aircast with you’re mixer by following the configuration pictures.\\ | In this Easy setup manual you’ll learn how to set up Aircast with you’re mixer by following the configuration pictures.\\ | ||
Line 47: | Line 47: | ||
To use the Fader starts of an Airlab you'll also need to set the Serial port settings to the right Baud rate.\\ | To use the Fader starts of an Airlab you'll also need to set the Serial port settings to the right Baud rate.\\ | ||
- | {{ :supaircast: | + | [[start:|{{:iconhome.png?100|Home}}]][[SupAirlite:start|{{:iconback2.png?100|Back}}]][[aircastairlite2:start|{{:iconforw.png?100|please follow |
- | For the non visual configuration you can go to the Aircast Control panel.\\ | + | |
- | + | ||
- | {{ :supaircast: | + | |
- | {{ :supaircast: | + | |
- | On this front you see the inputs and outputs highlighted with colors to easily recognize them.\\ | + | |
- | + | ||
- | {{ :supaircast: | + | |
- | {{ : | + | |
- | {{ : | + | |
- | On this backplane you see the inputs and outputs highlighted with colors to easily recognize them.\\ | + | |
- | + | ||
- | {{ : | + | |
- | Here you see the Windows Sound settings with the corresponding inputs highlighted with colors to easily recognize them.\\ | + | |
- | + | ||
- | {{ :supaircast: | + | |
- | Here you see the Windows Sound settings with the corresponding outnputs highlighted with colors to easily recognize them.\\ | + | |
- | + | ||
- | {{ :supaircast: | + | |
- | * Player 1 plays to Channel 1 and it’s PFL goes to Channel 4\\ | + | |
- | * Player 2 plays to Channel 2 and it’s PFL goes to Channel 4\\ | + | |
- | * Player 3 plays to Channel 3 and it’s PFL goes to Channel 4\\ | + | |
- | * The standard playout goes to Channel 1, the standard PFL goes to Channel 4, the standard recording device is Program (Non Stop)\\ | + | |
- | + | ||
- | {{ : | + | |
- | * All the Cartwall players playout to channel 4 | + | |
- | + | ||
- | {{ : | + | |
- | * To listen to the encoder you can select Channel 4\\ | + | |
- | * it’s line in signal comes from the Prog (Non Stop).\\ | + | |
- | * as an Aux signal it receives the Aux.\\ | + | |
- | * The PFL player comes out of Channel 4.\\ | + | |
- | + | ||
- | * For the Voicetrack recorder we tell Aircast that Player A is Channel 1.\\ | + | |
- | * Player B is Channel 2.\\ | + | |
- | * Cartwall is Channel 4 as well as the Mic Monitor.\\ | + | |
- | * The Microphone input is the Sub / Voice track bus. | + | |
- | + | ||
- | {{ : | + | |
- | + | ||
- | * To record the Aircheck you can use different inputs.\\ | + | |
- | * in this case we selected Prog (Non Stop) but this can also be the on air input at an Airlite.\\ | + | |
- | * The Live Feed uses the Prog (Non stop) input.\\ | + | |
- | + | ||
- | {{ : | + | |
- | To control Aircast with you’re D&R mixer you’ll have to add the Remote Control function of the specific mixer.\\ | + | |
- | + | ||
- | {{ : | + | |
- | You’ll have to tell Aircast that Player 1 uses the channel USB 1.\\ | + | |
- | + | ||
- | {{ : | + | |
- | {{ : | + | |
- | Player 2 uses the channel USB 2\\ | + | |
- | + | ||
- | {{ : | + | |
- | {{ : | + | |
- | and Player 3 uses the channel USB 3 this way the Fader starts will work fort his channel. | + | |
- | + | ||
- | {{ : | + | |
- | {{ : | + | |
- | For the Cartwall we use the 8 buttons in Row A, it is also possible to change the colors of the Led’s. | + | |
- | + | ||
- | {{ : | + | |
- | {{ : | + | |
- | For the other switches that arent used for the Cartwall players we can configure different fucntions.\\ | + | |
- | Keep in mind that the switches in Row A (1, 3, 5, 7, 9, 11, 13, 15) are already in use and have to be empty.\\ | + | |
- | + | ||
- | {{ : | + | |
- | {{ : | + | |
- | Be sure that the Port numbers correspond with the Port numbers in Airlite Control | + | |
- | + | ||
- | {{ : | + | |
- | An Airlab sends it's Fader starts trough Serial port.\\ | + | |
- | + | ||
- | {{ : | + | |
- | These have to be configured on the Airlab his Channel positions.\\ | + | |
aircastairlite/start.1544436047.txt.gz · Last modified: 2018/12/10 11:00 by support