airlitefix:start
Differences
This shows you the differences between two versions of the page.
| Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
| airlitefix:start [2020/05/28 16:18] – support | airlitefix:start [2022/07/18 09:07] (current) – support | ||
|---|---|---|---|
| Line 1: | Line 1: | ||
| - | \\ | ||
| **__Question: | **__Question: | ||
| \\ | \\ | ||
| Line 60: | Line 59: | ||
| === Be sure that the unit is unplugged from the power source! === | === Be sure that the unit is unplugged from the power source! === | ||
| \\ | \\ | ||
| + | ===To swap a Airlite 4x P.C.B. or backplane you don't have to disassamble the complete unit!=== | ||
| \\ | \\ | ||
| + | {{: | ||
| + | \\ | ||
| + | To open an Airlite you need to remove all the Potentiometer knobs and fader knobs.\\ | ||
| + | \\ | ||
| + | \\ | ||
| + | {{: | ||
| + | \\ | ||
| + | Remove the screws in the Red circles at the picture.\\ | ||
| + | \\ | ||
| + | \\ | ||
| + | {{: | ||
| + | \\ | ||
| + | The Airlite 4x is situated at the bottom side of the Main P.C.B..\\ | ||
| + | \\ | ||
| + | \\ | ||
| + | {{: | ||
| + | \\ | ||
| + | Remove the screws in the Red circles at the picture and all the potentiometer nuts.\\ | ||
| + | \\ | ||
| + | \\ | ||
| + | ------- | ||
| + | \\ | ||
| + | ====How to remove the Power supply==== | ||
| + | \\ | ||
| + | {{: | ||
| + | \\ | ||
| + | The power supply is located at the right side.\\ | ||
| + | \\ | ||
| + | \\ | ||
| + | {{: | ||
| + | \\ | ||
| + | Remove the screws in the Red circles at the picture.\\ | ||
| + | \\ | ||
| + | \\ | ||
| + | {{: | ||
| + | \\ | ||
| + | Remove the screws in the Red circles at the picture.\\ | ||
| + | \\ | ||
| + | ----- | ||
| + | \\ | ||
| + | ====How to remove the backplane==== | ||
| + | \\ | ||
| + | {{: | ||
| + | \\ | ||
| + | Remove the screws in the Red circles at the picture.\\ | ||
| + | \\ | ||
| + | \\ | ||
| + | {{: | ||
| + | \\ | ||
| + | Remove the screws in the Red circles at the picture.\\ | ||
| + | \\ | ||
| + | \\ | ||
| + | {{: | ||
| + | \\ | ||
| + | Remove the screws in the Red circles at the picture.\\ | ||
| + | \\ | ||
| + | -------- | ||
| + | \\ | ||
| + | ====Where to place the AES3 module in an Airlite==== | ||
| + | \\ | ||
| + | {{: | ||
| + | \\ | ||
| + | The position of the AES3 board is on these pin strips at the backplane.\\ | ||
| + | This can be installed easily if you need an Master to AES3 output at a later moment.\\ | ||
| + | \\ | ||
| + | -------- | ||
| + | \\ | ||
| + | ====Where to measure the Power supply in an Airlite==== | ||
| + | \\ | ||
| + | {{: | ||
| + | \\ | ||
| + | The ground is marked with a Green dot.\\ | ||
| + | The Red dot is the Possitive (+ 15 Volt) voltage.\\ | ||
| + | The Blue dot is the Possitive (- 15 Volt) voltage.\\ | ||
| + | The Purple dot is the Logic (+ 5 Volt) voltage.\\ | ||
| + | The Purple dot is the Phantom power (+ 48 Volt) voltage.\\ | ||
| + | \\ | ||
| + | \\ | ||
| + | {{: | ||
| + | \\ | ||
| + | In this picture you can see an overview of the Power distribution.\\ | ||
| \\ | \\ | ||
| ----- | ----- | ||
| Line 69: | Line 149: | ||
| If you have questions, please consult the factory by filling in our Support Request form.\\ | If you have questions, please consult the factory by filling in our Support Request form.\\ | ||
| \\ | \\ | ||
| - | [[https:// | + | [[https:// |
| - | \\ | + | |
| - | Go back to the [[SupAirlite: | + | |
| \\ | \\ | ||
| + | [[start: | ||
airlitefix/start.1590675488.txt.gz · Last modified: 2020/05/28 16:18 by support