Differences

This shows you the differences between two versions of the page.

--- axumaes67usb:start [2019/07/23 09:12] – support
+++ axumaes67usb:start [2022/07/18 09:17] (current) – support
@@ Line 3: / Line 3: @@
 **__Answer:__** Link: [[AxumAES67USB:start|follow the instructions on this page.]] \\
 \\
+-----
+\\
+==== The "AES67/USB card" will only work completely in 16 channel slots of the Axum rack positioned between the DSP card and the Rack ETX. ====
+\\
+==== In units produced after 05-05-2021 the AES67/USB card will work from slot 12 and higher due to a firmware update. ====
 \\
 -----
 \\
-==== The "AES67 / USB card" needs to be the "Word Clock" for the system. ====
+==== Because the "AES67/USB card" is developed recently it's settings aren't available for "Import" at the "Rack configuration". ====
+\\
+There for the settings need to be added manually.\\
+\\
+-----
+\\
+==== The "AES67/USB card" needs to be the "Word Clock" for the system. ====
 \\
 If the "Word Clock" is provided by a different card like for example the "Fire Wire card" the audio will be distorted.\\
 \\
-This is why the "AES67 / USB card" and the "Fire Wire card" can't be used together in one system.\\
+This is why the "AES67/USB card" and the "Fire Wire card" can't be used together in one system.\\
+\\
+You can set the "AES67/USB card" to be "Word Clock" by clicking it's dot under "WC" at the "Rack configuration".\\
+\\
+{{ :axumaes67usb:usbwcb.png?direct |}}
+\\
 \\
 -----
+\\
+{{ :axumaes67usb:usboutputsb.png?direct |}}
+\\
+First configure the outputs of the "AES67/USB card" by pressing "Create new source".\\
+\\
+\\
+{{ :axumaes67usb:usbinputsb.png?direct |}}
+\\
+Then configure the Inputs of the "AES67/USB card" by pressing "Create new destination".\\
+\\
 \\
 {{ :axumaes67usb:usb_settings_1.png?direct |}}
 \\
 The __"AES67-USB-in-x-Level"__ has to be set to __"-18"__ for the best results and can be tweaked afterwards.\\
+\\
 \\
 {{ :axumaes67usb:usb_settings_2.png?direct |}}
 \\
 The __"AES67-USB-out-x-Level"__  has to be set to __"15"__ for the best results and can be tweaked afterwards.\\
+\\
 \\
 {{ :axumaes67usb:usb_settings_3.png?direct |}}
 \\
 The AES67 / USB card can only work in one mode at a time.\\
+\\
 \\
 When you set the __"AES67-USB-Streaming-Interface"__ setting to __"0"__ it will activate the __"AES67"__ function.\\
@@ Line 31: / Line 60: @@
 \\
 \\
-[[https://www.d-r.nl/support-request.html|Support Request]]\\
+{{ :axumaes67usb:console1-4-global_config.png?direct |}}\\
+\\
+The __"Sample rate"__ at the __"Global Configuration"__ page needs to be the same as in the __"Archwave USB Driver Control Panel"__.\\
+\\
+\\
+{{ :axumaes67usb:archwave_control_panel_1.png?direct |}}
+\\
+The __"Archwave USB Driver Control Panel"__ can be found here after installation.\\
+\\
+\\
+{{ :axumaes67usb:archwave_control_panel_2.png?direct |}}
+\\
+At the __"Synchronisation"__ tab you can change the __"Sample rate"__ settings of the Archwave card.\\
+\\
+\\
+------
+\\
+==== How to use 2x AES67/USB card both in USB mode. ====
+\\
+Connect both AES67/USB cards with a network cable to your network.\\
+\\
+You'll need to download Putty to be able to make a Telnet connection for setting the Synchronization mode!\\
+\\
+[[https://www.chiark.greenend.org.uk/~sgtatham/putty/latest.html|Putty download page]]\\
+\\
+You also need to download this windows script by "Save link as".\\
+\\
+[[http://www.mambanet.org/wiki/dokudata/faq/axum/AES67USB Telnet Putty Script.wsf|AES67USB Telnet Putty Script]]\\
+\\
+\\
+{{:axumaes67usb:2xusb1.png?direct|}}
+\\
+First set both cards Word Clock enabled to "0" (OFF), and "AES67-USB-Streaming-Interface" to "1" (USB mode).\\
+\\
+\\
+{{:axumaes67usb:2xusb2.png?direct|}}
+\\
+Set the Word Clock to the "Axum MambaNet Gateway".\\
+\\
+Find out which IP Addresses your AES67/USB cards have, edit the script file to change the IP address and run the script file.\\
+\\
+Also change the IP address for the second card and run the script file.\\
+\\
+Reboot the system!\\
+\\
+\\
+Both cards now work with the Word Clock of the Axum system and are able to play and record without glitches.\\
+\\
+\\
+We are still working on a solution to be able to work both cards in AES67 mode without glitches!\\
+\\
+------
+\\
+\\
+[[https://www.dnrbroadcast.com/support-related|Support Request]]\\
 \\
-Go back to the [[SupAxum:start|Axum]] support page.\\
+[[start:|{{:iconhome.png?100|Home}}]][[SupAxum:start|{{:iconback2.png?100|Back}}]]
 \\